Please note ā this 100 Watt PV Logic Flexi Panel Kit has a rear exit for the connecting cable.
From the 5 Watt to the 120 Watt Solar Panel, PV Logic Flexi is well suited for use where a super robust, low profile and lightweight panel is needed, or the substrate to which the panel will be fixed has a slight curve. Ideal for marine buoys, boat decks, camper vans etc.
Underside cable exit (100w and 150w panels only)
The cable of the 100w and 150w flexi panels exits the panel from the underside allowing for a completely flush fit to your roof or decking. A remote shading diode box ensures consistent performance even in partially shady conditions. The 100w and 150w panels are available with a white back sheet or all black.
Flexi offers the following advantages:
Self-healing top surface
The ETFE top layer gives the PV Logic Flexi extra resilience in really tough conditions. ETFE has a memory effect or self-healing capacity in the event the panel comes into contact with branches etc, thus ensuring any slight abrasions are āhealedā within a few hours. The Flexi range can even be walked on with soft deck shoes! During production, the ETFE is dimpled to further protect the panel and provide an anti-slip surface, particularly useful if the panel is fitted to a boat deck.
Completely waterproof
Each panel is assembled to ensure complete encapsulation. This ensures the 6 layer heavy duty laminate protects the solar cell circuit from extreme conditions. The junction box is also injected with special silicon, guaranteeing no water ingress.
Superior design
There are no square edges on a PV Logic Flexi! Rounded panel corners and a unique curved junction box provide superior adhesion, no snag lamination and no sharp edges. The junction box is mechanically fixed in addition to being bonded to the panel. Strain relief is provided for the fitted 4m UV stabilised PV cable ensuring it cannot be accidentally pulled from the junction box.
Easy fix
The Flexi range can be bonded to flat or slight curved surfaces (3cm curve per metre) such as painted aluminium, metal, GRP and fibreglass using Simson ISR 70-03. The aluminium layer is also pre-drilled with 4.5mm holes should the panel need to be mechanically fixed as well as or instead of bonding.
Warranty
The Flexi range is setting new standards with a 2-year product and a 20-year performance warranty *.
*Cell performance warranty states that at 20 years the cell output will be no less than 80% of new performance values ā i.e the cell degradation rate will be no greater than 20% in 20 years
Specifications
Power (Wp)
100 watts
Nominal Voltage (Vmp)
18V DC
Nominal Current (Imp)
5.37A
Open Circuit Voltage (Voc)
22.32V
Short Circuit Current (Isc)
5.74A
Operating Temperature
-40 to + 80 Deg C
Max System Voltage
750V DC
Dimensions
980x690x3.5mm
Weight
4.2Kg
Approx. watt-hours/day**
600W
Approx. amp-hours/day**
32.2A
** Based onĀ 6 hours of average daily peak sunlight hours
Contents
1 xĀ STPVF100 ā 100wp solar panel (Rear Cable exit)
1 x 4m Cable (attached)
1 x Fuse
6 x Ring Terminals
1 x Instruction Sheet
***Cell performance warranty states that at 20 years the cell output will be no less than 80% of new performance values ā i.e. the cell degradation rate will be no greater than 20% in 20 years
Please note.
All of our semi flexible panels will only bend from the top (has the cable and logos) to the bottom a maximum of 10% of panel length.
Bending the panel greater than this or trying to bend the panel from left to right will possibly damage the panel and also invalidate your warranty.
Installation method
Please only use the glue pattern below (this is covered in more detail in the instructions), which ensures air flow under the panel is achieved preventing heat build-up and potential warping under extreme heat.